airbrush action latest issue airbrush action magazine subscribe
airbrush action magazine
airbrush action magazine subscribeairbrush action magazine subscribe airbrush action magazine subscribe

FOLLOW US and
LEARN MORE!

Artool 6 – Craig Fraser Mastering Diamond Plate

first       first

For the uninitiated, this column instructs on the use and techniques of all stencils in the innovative Artool line, from Skullmasters to FX to Flame-A-Rama, and anything else we have laser cut out of plastic.

In the previous column I demonstrated the use of Bullet Ridden, the first stencil in the FX line. Following suit, we dig up Diamond Plate, an oldie but a goodie because I have rendered this effect with stencils for more than a decade. In my first video, I hand-cut the sucker out of an 8×10 photograph. Then, in my book Automotive Cheap Tricks & Special F/X, I performed the effect with the design cut on vinyl using a plotter. Currently, my preference is the laser-cut freehand stencils because I don’t have to spend hours cutting them with an X-Acto knife…..hehehh. The computer-cut vinyl is still a good technique, but for small areas, and over paint where you might worry about tape tracking, the freehand shields are usually the best bet.

The diamond plate effect can be used for anything from a background graphic to main applications in murals. Although it’s a simple effect, I still receive a fair share of questions regarding this stencil’s use.

Step 1:

step 1

After masking off the powder coated panel, I scuff the heck out of the surface. Normally, I would just scuff it enough to get the paint to stick, but in this case I’m going to use some of ALSA’s Ghost Chrome for a brushed aluminum effect. The extra scratches I give the panel make the effect even more realistic.

Step 2:

step 3

Using the new Iwata trigger airbrush, I spray on a few layers of Ghost Chrome. This new trigger sidefeed model sprays the Ghost Chrome pretty killer without layering it too heavy. This airbrush is also beneficial to painters who are used to using sprayguns. With the Ghost Chrome layered evenly, the panel now looks just like a brushed sheet of aluminum.

Step 3:

step 3

For large surfaces, consider purchasing more then one stencil to eliminate the down-time required to clean off the wet paint from the stencil. (No, this is not a shameless plug,…..well,…actually it is.)

Step 4:

step 4

Before spraying, I like to protect the edges from overspray using masking tape. The tap

first       first

For the uninitiated, this column instructs on the use and techniques of all stencils in the innovative Artool line, from Skullmasters to FX to Flame-A-Rama, and anything else we have laser cut out of plastic.

In the previous column I demonstrated the use of Bullet Ridden, the first stencil in the FX line. Following suit, we dig up Diamond Plate, an oldie but a goodie because I have rendered this effect with stencils for more than a decade. In my first video, I hand-cut the sucker out of an 8×10 photograph. Then, in my book Automotive Cheap Tricks & Special F/X, I performed the effect with the design cut on vinyl using a plotter. Currently, my preference is the laser-cut freehand stencils because I don’t have to spend hours cutting them with an X-Acto knife…..hehehh. The computer-cut vinyl is still a good technique, but for small areas, and over paint where you might worry about tape tracking, the freehand shields are usually the best bet.

The diamond plate effect can be used for anything from a background graphic to main applications in murals. Although it’s a simple effect, I still receive a fair share of questions regarding this stencil’s use.

Step 1:

step 1

After masking off the powder coated panel, I scuff the heck out of the surface. Normally, I would just scuff it enough to get the paint to stick, but in this case I’m going to use some of ALSA’s Ghost Chrome for a brushed aluminum effect. The extra scratches I give the panel make the effect even more realistic.

Step 2:

step 3

Using the new Iwata trigger airbrush, I spray on a few layers of Ghost Chrome. This new trigger sidefeed model sprays the Ghost Chrome pretty killer without layering it too heavy. This airbrush is also beneficial to painters who are used to using sprayguns. With the Ghost Chrome layered evenly, the panel now looks just like a brushed sheet of aluminum.

Step 3:

step 3

For large surfaces, consider purchasing more then one stencil to eliminate the down-time required to clean off the wet paint from the stencil. (No, this is not a shameless plug,…..well,…actually it is.)

Step 4:

step 4

Before spraying, I like to protect the edges from overspray using masking tape. The tape also allows you to position and hold the stencil, leaving your other hands free to control the airbrush. I don’t recommend spray adhesive for stencil holding. For automotive this can cause some serious issues with contamination.

Step 5:

step 5

Loading the airbrush with House of Kolor BC-25 basecoat black, I lightly dust the individual diamond shapes with an Eclipse HP-CS. Don’t apply too much paint at once or the stencil will get too wet, unusable, and may cause the paint to creep underneath.

Step 6:

step 6

After the first layer of paint is applied, I come in with a heavier coat, but only on the bottom edge of the diamond shape. This gives a natural 3- D look to your piece. This technique is also used to show a curvature or shadow on any small stenciled objects, such as rivets.

Step 7:

step 7

When I run out of stencil, I remove the sheet and reposition it lower to fill the rest of the panel. I recommend overlaying at least one row of diamonds to get the line-up just right. The stencil can be tiled endlessly.

Step 8:

step 8

Still using black, I freehand the dropshadows. Without shadowing, the diamonds won’t have depth. Spray the drop-shadow lightly or you risk ruining the effect.

Step 9:

step 9

Remember the mention of rivets a few pics back? Well, what a coincidence that we get to practice them now. A number of my stencils have different circles in them that you can use for rivets. In this case, I use the original Skullmaster Frontal stencil. Heck, an architectural circle template will work just as well.

Step 10:

step 10

With the black finished, I then use HoK BC-26 basecoat white. The bottom half of the Diamond Plate has some half stencils that are used for the highlights. Lining up one row of diamonds at a time, I spray in the top highlight of each.

Step 11:

step 11

Next, I freehand a small glowing dot onto the top center of each one. Without the stencil, the freehand dots create a realistic glow around the diamonds. If the white is not extra thinned down, you’ll get spitting, which will truly “jack up” your realistic highlights.

Step 12:

step 12

Normally, I recommend adding a few drops of the base color silver to your black, and white to keep the highlights in a more realistic plane. By itself, the white will look like it’s floating above the rendering. The cool thing about Ghost Chrome is that it’s so thin you can dust a light coat over everything, and that puts all the values of the piece back into perspective. I use my trigger gun to spray a light dust coat. For larger areas, I recommend a small touch-up gun. Well, there you have it; a nice piece of realistic diamond plate easily rendered with your new best friend from the FX stencil collection. Any time you start to believe that stencils are for beginners, and that you’re too good an airbrusher to use them, just imagine how much fun it would be to freehand render each one of those little suckers on a car! Yeah….not a good visual, is it?! Tune in next issue for the continuation of the stencil series. If you have any comments, suggestions, or requests, please submit them to Craig Fraser at Fraser@gotpaint.com Paint to live, live to paint,……and sometimes with stencils… Fraser

e also allows you to position and hold the stencil, leaving your other hands free to control the airbrush. I don’t recommend spray adhesive for stencil holding. For automotive this can cause some serious issues with contamination.

Step 5:

step 5

Loading the airbrush with House of Kolor BC-25 basecoat black, I lightly dust the individual diamond shapes with an Eclipse HP-CS. Don’t apply too much paint at once or the stencil will get too wet, unusable, and may cause the paint to creep underneath.

Step 6:

step 6

After the first layer of paint is applied, I come in with a heavier coat, but only on the bottom edge of the diamond shape. This gives a natural 3- D look to your piece. This technique is also used to show a curvature or shadow on any small stenciled objects, such as rivets.

Step 7:

step 7

When I run out of stencil, I remove the sheet and reposition it lower to fill the rest of the panel. I recommend overlaying at least one row of diamonds to get the line-up just right. The stencil can be tiled endlessly.

Step 8:

step 8

Still using black, I freehand the dropshadows. Without shadowing, the diamonds won’t have depth. Spray the drop-shadow lightly or you risk ruining the effect.

Step 9:

step 9

Remember the mention of rivets a few pics back? Well, what a coincidence that we get to practice them now. A number of my stencils have different circles in them that you can use for rivets. In this case, I use the original Skullmaster Frontal stencil. Heck, an architectural circle template will work just as well.

Step 10:

step 10

With the black finished, I then use HoK BC-26 basecoat white. The bottom half of the Diamond Plate has some half stencils that are used for the highlights. Lining up one row of diamonds at a time, I spray in the top highlight of each.

Step 11:

step 11

Next, I freehand a small glowing dot onto the top center of each one. Without the stencil, the freehand dots create a realistic glow around the diamonds. If the white is not extra thinned down, you’ll get spitting, which will truly “jack up” your realistic highlights.

Step 12:

step 12

Normally, I recommend adding a few drops of the base color silver to your black, and white to keep the highlights in a more realistic plane. By itself, the white will look like it’s floating above the rendering. The cool thing about Ghost Chrome is that it’s so thin you can dust a light coat over everything, and that puts all the values of the piece back into perspective. I use my trigger gun to spray a light dust coat. For larger areas, I recommend a small touch-up gun. Well, there you have it; a nice piece of realistic diamond plate easily rendered with your new best friend from the FX stencil collection. Any time you start to believe that stencils are for beginners, and that you’re too good an airbrusher to use them, just imagine how much fun it would be to freehand render each one of those little suckers on a car! Yeah….not a good visual, is it?! Tune in next issue for the continuation of the stencil series. If you have any comments, suggestions, or requests, please submit them to Craig Fraser at Fraser@gotpaint.com Paint to live, live to paint,……and sometimes with stencils… Fraser

Speak Your Mind

* Email
 First Name
 Last Name
  * = Required Field
 
Email Marketing You Can Trust